Sheave φ1270 101.51.20.02 1

Bearing φ260Xφ360X134 GB299-86(2097952K)

Cantilever sheave set  Sheave φ720/56 111.53.16.01 1

 

Bearing 170×280×150 GB299-86(2097734K) 1

Screw plug M10×1 111.53.16.02 1

Cantilever sheave shaft 111.53.16.03 1

Bolt M20×55 GB32.1-88(M20×55-8.8) 8

Washer 20 GB93-87(20) 8

Wire lineφ2 L=400 GB343-82(φ2) 4

Baffle plateδ20 111.53.16.04 1

Bolt M24×50 GB32.1-88(M24×50-8.8) 3

Washer 24 GB93-87(24) 3

Spacer φ190/φ170 111.53.16.05 1

Felt ring 190 111.53.16.06 2

Through cover(Ⅰ) 111.53.16.07 1

Adjustable mat t=0.2/t=0.5 111.53.16.08 　

Oil cup M10×1 GB1152-79(M10×1) 1

Through cover Ⅱ 111.53.16.09 1

Locating blockδ10 111.53.16.10 2

Washer 160 GB858-88(160) 1

Round nut M160×3 111.53.16.11 1

Foot block δ14 111.53.16.12 1

Baffle plate 111.53.16.13 1

Bolt M16×35 GB32.1-88(M16×35-8.8) 2

Washer 16 GB93-87(16) 2

Dual standpipe device 　 　

Pipe grapple 111.53.211.00 12

Eye bolt in tail M24×80 GB31.1-88(M24×80-8.8) 24

Slotted nut M24 GB6178-86(M24-8) 24

Washer 24 GB97.1-86(24) 24

Cotter pin 5×40 GB91-86(5×40) 24

Monkey board

Pinφ50×105 111.53.00.04 6

Safety pinφ10×75 111.53.00.05 4

Clip 60×φ30×φ3 111.53.00.03 18

Lifting tackle H1x1KBL 3

Pulling device 111.53.256.00 3

Pinφ30×80 111.53.250.01 12

Chainlet 9 L=400 GB5802-86(φ9-400) 2

Bolt M12×40 GB31.1-88(M12×40-8.8) 4

Slotted nut M12 GB6178-86(M12-8) 4

Washer 12 GB97.1-85(12) 4

Cotter pin 3.2×30 GB91-86(3.2×30) 4

Bayshon assy 　 　

Eye bolt in tail M12×80 GB31.1-86(M12×80-6.8) 15

Slotted nut M12 GB6178-86(M12-6) 24

Spring washer 12 GB93-87(12) 24

Cotter pin 3.2×22 GB91-86(3.2×22) 24

Eye bolt in tail M12×100 GB31.1-86(M12×100-6.8) 9

Cagged ladder assy. 　 　

Bolt M16×60 GB31.1-88(M16×60-8.8) 48

Slotted nut M16 GB5178-88(M16-8) 48

Washer 16 GB93-87(16) 48

Cotter pin 4×28 GB91-86(4×28) 48 　

Pinφ100×400 111.53.400.01 4

Safety pinφ20×150 111.53.00.02 6

Clip 60×φ30×φ3 111.53.00.03 20

Wire line stop roller 111.53.15.00 2

Cantilever sheave of A-frame 111.53.406.00 2

Pinφ70×380 111.53.400.02 4

Safety pinφ15×90 111.53.00.08 4

Pinφ100×480 111.53.400.03 2

U-bolt M42 111.53.400.04 4

Pressboardδ50 111.53.400.05 4

Slotted nut M42×3 GB6178-86(M42×3-8) 8

Cotter pin 6.3×65 GB91-86(6.3×65) 8

Drawbar 111.53.411.00 2

Oil tube stabbing board 　 　

Shackle 8.5T S-BX8.5-1 4

Pinφ50×105 111.52.00.04 2

Clip 60×φ30×φ3 111.53.00.03 6

Safety pin φ10×75 111.53.00.05 2

Pinφ40×90 111.53.380.01 4

Fast line sheave assy. 101.51.20.00 1

Sheave set assy. 101.51.40.00 1

Auxiliary sheave assy. I 101.51.70.00 1

Auxiliary sheave assy. II 101.51.80.00 2

Slotted nut M10 GB6178-1986(M10-8) 8

Bolt M10X70 GB/T31.1-1988(M10X70-8.8) 8

Washer 10 GB/T97.1-1986(10) 8

Cotter pin φ2.5X20 GB91-86(2.5X20) 8

Eye bolt in tail M30X120 GB31.1-86(M30X120-8.8) 8

Slotted Nut M30 GB6178-86(M30-8) 8

Washer 30 GB93-87(30) 8

Cotter pin φ6.3X50 GB91-86(φ6.3X50) 8

Eye bolt in head M16X35 GB32.1-1986(M16X35-8) 8

Washer 16 GB/T93-1987(16) 8

Clip 120Xφ60Xφ6 101.51.00.01 13

Eye bolt in tail M24X120 GB31.1-86(M24X120-8.8) 8

Slotted nut M24 GB6178-86(M24-8) 8

Washer 24 GB93-87(24) 8

Cotter pin 5X40 GB91-86(5X40) 8

Wire line stop device III 101.51.145.00 1

O-matic 101.53.150.00 1

Gin pole of crown block 　 　

Pin φ40X90 101.51.10.04 4

Clip 60Xφ30Xφ3 101.51.10.05 8

Cross drawbar 101.51.13.00 2

Pipe φ76X5 L=840 101.51.10.06 1

Pipe φ76X5 L=970 101.51.10.07 2

Pin φ30X80 101.51.10.08 4

Bolt M20X50 GB31.1-86(M20X50-8.8) 16

Nut M20 GB6178-86(M20-8) 16

Washer 20 GB93-87(20) 16

Cotter pin 4X36 GB91-86(4X36) 16

5T Manual I-beam trolley SG-5 1

O-matic device 101.53.151.00 　

Safety chain 101.53.152.00 　

Bolt M20X185 101.53.150.01 　

Slotted nut M20 GB6178-86(M20-8) 　

Washer 20 GB93-87(20) 　

Cotter pin 4X36 GB91-86(4X36) 　 　

Bearing seat 101.51.40.01 2

Shaft 101.52.40.02 1

Spacer 101.51.40.03 2

Dust ring 101.51.20.04 12

Bearing 260X360X134 Bearing 260X360X134 6

Sheave φ1270 101.51.20.02 6

End shield 101.51.20.01 2

Bolt M20X45 GB/T32.1-1988(M20X45) 8

Washer 20 GB/T93-1987(20) 8

Iron wire φ2 GB343-82(φ2) A.R.

Oil cup M10X1 GB1152-89(M10X1) 6

Plug M24 101.51.20.07 2 　

End shield 101.51.20.01 2

Lock pawl—left	105.06.1
Lock pawl—right	105.06.2
Pin,handle lock pawl	105.06.03-1
Grease fitting	GB1152-89 (M10X1)
Grease fitting
Pin,lock pawl	105.11.01
Plug	105.06.05 (1/8")
Screw, hex soc hd	105.06.10.00
Grease fitting	GB70-85 (M24X75)
Plate, I.D	105.11.27
Screw	GB67-85 (M4X8)
Dipstick, oil	105.11.10.0
Plug	105.06.07 (1 1/2')
Housing	105.11.20.00
Tongue	105.11.03
Cover	105.11.30.00
Ring gear (spiral teeth)	105.11.31
Ring gear (bevel ing teeth)	105.11.28
Bearing	91682/530
Table	105.11.05-1

Lock pawl	105.11.50.00
Pin	105.11.24
Pin,cotter 5X36	GB91-86
Pin,cotter 5X36
Kelly bushing	105.11.30(3 1/2")
Kelly bushing	105.11.32(5")

Master bushing	105.11.29
Bearing	1689/520
Shim
Shim
Shim	105.11.10
Pinion shaft assembly	105.11.40.00
Drain plug 1"
Seal	105.11.18
O ring	105.11.14
Screw	105.11.17(M20*65)
Washer,spring 20	GB93-87
Shim	105.11.15
Shim	105.11.16
Support, bearing	105.11.12
Screw	GB5783-86(M16X40)
Washer, spring 16	GB93-87
SIinger	105.11.13
O-Ring	105.11.11
Chain wheel	105.11.21-1
Sprocket retainer
Flange	105.11.19

Lift hook	105K.11.21
Lift hook
Pinion shaft assembly	105.11.40.00
	105.11.40.12
	105.11.40.13
End-plate of bearing	105.11.40.02
Bearing	32622EH
O-Ring	105.11.40.03
Spacer	105.11.40.04
Drain plug 1"
Drain plug 1"	105.08.60.01
Magnet	105.08.60.02
Pin,cotter 2X12	GB91-86
Shaft, pinion	105.11.40.05
Bearing	53622H
Screw
Screw	GB5783-86(M20X60)
Screw	GB5783-86(M16X50)
Washer,spring 20
Washer,spring 20	GB93-87
Washer,spring 16	GB93-87
Shim	105.11.40.06
Capsule	105.11.41.00
Shim	105.11.40.07
Seal，oi	D7-1-67(140*170*15)
Retainer, pinion end
Retainer, pinion end	105.11.40.10
Nut, pinion shaft
Pinion shaft housing	105.11.40.08
Key	105.11.40.09
Sprocket retainer	C6-3-92(125)
Screw with head holes
Screw with head holes	GB32.1-88

TAG：